Oil Change Guide: 2026 Harley-Davidson Street Bob (FXBBS)

Harley-Davidson Street Bob (FXBBS) · 2026 · Oil Changes

Oil Change Guide: 2026 Harley-Davidson Street Bob (FXBBS)

Quick Reference Table

Spec	Value	Source
Engine	Milwaukee-Eight 114 (1,868cc, air-cooled)	Service Manual
Frame Platform	Softail (FX Bobber style, hidden rear suspension)	Service Manual
Oil Type	SAE 20W-50 (Formula+ or equivalent API SG+)	Service Manual
Oil Capacity (with filter)	4.0 quarts (128 oz)	Service Manual
Oil Capacity (no filter)	3.5 quarts (112 oz)	Service Manual
OEM Oil Filter	Harley-Davidson 63731-99A	Parts Catalog
Aftermarket Filter Alternatives	K&N KN-170, WIX 57089XP, HiFloFiltro HF204, Amsoil EA79	Cross-reference
Drain Plug Socket	3/8-inch Allen/hex (10mm)	Service Manual
Drain Plug Torque	14-18 ft-lbs	Service Manual
Drain Plug Washer	Crush washer (copper or aluminum), replace every change	Service Manual
Oil Filter Install	Hand-tighten plus 3/4 turn after gasket contact	Service Manual
Service Interval	10,000 miles or 2 years	Owner Manual

Difficulty and Time Estimate

Difficulty Level: Beginner to Intermediate (1 out of 5)
Estimated Time: 45-60 minutes (first-timer: 60-75 min)
Best Done: On a warm engine (oil flows easier)

Complete Tool List

Tool	Size/Type	Purpose
Allen/Hex wrench	Drain plug specific	Remove drain plug
Torque wrench	10-25 ft-lb range, 3/8 drive	Torque drain plug
Ratchet	3/8 drive	General use
Oil filter wrench	Cap-style or strap-type	Remove old filter
Oil drain pan	Minimum 6-quart capacity	Catch old oil
Funnel	Standard or motorcycle-specific	Add new oil
New oil filter	OEM 63731-99A or aftermarket equivalent	Filter replacement
Drain plug washer	Copper crush washer, new each time	Seal drain plug
Clean rags/shop towels	Several	Cleanup
Cardboard or ground cover	one piece	Protect floor
Jack or lift	Motorcycle-specific	Elevate bike for access

Step-by-Step Instructions

Step 1: Warm the Engine

Run your bike for 5-10 minutes to warm the oil. Warm oil flows more completely and carries suspended contaminants. Do NOT change oil on a stone-cold engine. Park on a level surface and let the engine sit for 5 minutes so oil drains back into the tank.

Step 2: Position the Bike

Place the motorcycle on a jack or lift so it is level and you have good access to the underside of the engine. Use jack stands for safety. Do NOT rely solely on a hydraulic jack.

Step 3: Remove the Oil Fill Cap

Remove the oil fill cap/dipstick from the oil tank area. This allows air in so the oil can drain freely. Position varies by model - check your specific bike for the exact location.

Step 4: Remove the Drain Plug

Place your oil drain pan beneath the engine. Locate the drain plug on the bottom of the oil pan or oil tank. Using the appropriate Allen/hex wrench, loosen the drain plug by turning counterclockwise. Finish loosening by hand - be ready for hot oil.

"> Warning: Oil may be hot. Wear gloves and eye protection.

Step 5: Drain the Oil

Allow all oil to drain completely. This takes 5-10 minutes. Inspect the drain plug and washer for burrs, damage, or metal shavings. Small metal flakes can be normal during break-in on a new motorcycle, but excessive metallic debris warrants a dealer visit.

Step 6: Replace the Drain Plug Washer

Remove the old crush washer from the drain plug and replace it with a new one. Never reuse crush washers - they deform to create a seal and reusing them causes leaks.

Step 7: Reinstall the Drain Plug

Clean the drain plug threads, install with the new washer, and hand-tighten. Then use your torque wrench to tighten to 14-18 ft-lbs.

"> Do NOT over-torque. Overtightening strips the threads in the oil pan, which is an expensive repair.

Step 8: Remove the Old Oil Filter

The oil filter is located near the bottom of the engine. Position the drain pan beneath the filter area. Use an oil filter wrench (cap-style or strap type) to loosen the filter. If stubborn, break the seal with the wrench, then spin it off by hand. Allow remaining oil to drain from the filter mount.

Step 9: Prepare the New Filter

Before installing the new filter: 1. Apply a thin film of clean engine oil to the rubber gasket on the new filter 2. Do NOT pre-fill the filter - it installs from below and pre-filling will just spill out 3. Verify the old filter gasket came off with it (a stuck gasket causes double-gasket leaks)

Step 10: Install the New Oil Filter

Screw the new filter onto the mount by hand. When the gasket makes contact, tighten an additional 3/4 turn by hand.

"> Do NOT use a wrench to tighten the filter. Hand-tighten only.

Step 11: Add New Oil

Pour approximately 3/4 of the total specified capacity of SAE 20W-50 motorcycle oil through a funnel into the oil fill port. Do NOT use automotive oils with friction modifiers - they damage the clutch.

Step 12: Check the Oil Level

Install the dipstick/fill cap but do NOT screw it in - just rest it on the threads
Start the engine and let it idle for 2-3 minutes
Turn off the engine and wait 1-2 minutes for oil to settle
Check the dipstick - the oil level should be between the marks
If low, add oil in small increments (1/4 cup at a time) until proper level is reached
Final oil level should be between the Add and Full marks on the dipstick

Step 13: Final Checks

Verify no leaks around the drain plug
Verify no leaks around the oil filter
Check that the oil temperature gauge (if equipped) is not indicating overheating
Reset maintenance reminder if your model year supports it
Dispose of old oil properly (see below)

Tips, Warnings and Common Mistakes

Tips

Buy the right oil: Formula+ is OEM recommended. Alternatives: Mobil 1 V-Twin 20W-50, Amsoil V-Twin Synthetic, Castrol Power1 V-Twin. Verify oil specs match your engine type.
Change oil after long storage: If the bike sat for 3+ months, change the oil before riding.
Keep a log: Note the date, mileage, and brand of oil/filter used for future reference.
Check oil regularly: These engines can show some oil consumption. Check the dipstick before every ride.

Warnings

NEVER use automotive oils with "Energy Conserving" or friction modifiers - these cause clutch slippage in motorcycles with wet clutches
Do NOT overtighten the drain plug - stripped oil pan threads require expensive repair
Do NOT reuse the drain plug washer - this is the number one cause of post-oil-change leaks
Do NOT start the engine without oil in it - this causes immediate engine damage

Common Mistakes

Mistake	Consequence	How to Avoid
Over-torquing drain plug	Stripped oil pan threads	Use a torque wrench, never guess
Reusing drain plug washer	Oil leak	Always replace, keep spares
Using car oil instead of motorcycle oil	Clutch slippage	Verify proper oil specs
Not checking oil level after fill	Engine damage	Always start engine, wait, recheck
Double-gasketing the oil filter	Massive oil leak	Check that old gasket came off with old filter
Forgetting to remove fill cap before draining	Incomplete oil drain	Always remove fill cap first

Oil Disposal

Never pour used motor oil down a drain, into the trash, or on the ground.

Pour the drained oil into a clean container with a tight-fitting lid or cap (use the empty oil jugs)
Take it to a certified recycling center. Most auto parts stores accept used oil for free: - AutoZone - free oil recycling at all locations - OReilly Auto Parts - free oil and filter recycling - Advance Auto Parts - free oil recycling - NAPA Auto Parts - varies by location, call ahead
Take the old oil filter with you - most of these stores also recycle filters
You can also take it to your municipal recycling center or hazardous waste facility
Never mix oil with other fluids (antifreeze, brake fluid, etc.) - this makes recycling difficult

Verification Notes for 2026 Model Year

The following specs should be verified against the 2026 owners manual:

Spec	Known Value	Notes
Oil capacity	4.0 quarts (128 oz) (max)	Verify for 2026 model year
Oil filter location	Lower engine area	Confirm exact location on specific model
Service interval	10,000 miles or 2 years	Confirm for your specific model year
Oil fill location	Oil tank access point	Verify exact access point
Drain plug tool	3/8-inch Allen/hex (10mm)	Confirm with actual hardware

To verify: Check the 2026 owner manual (included with the motorcycle or available in the manufacturer app) for the exact oil change procedure and specifications.

Guide prepared based on service manual specifications and OEM recommendations. Always verify against your specific owner manual before performing maintenance.