How to Replace Light Bulbs on a 2026 Harley-Davidson Road Glide Limited (FLTRK)

Harley-Davidson Road Glide Limited FLTRK · 2026 · Light Bulbs

Light Bulb Replacement Guide: 2026 Harley-Davidson Road Glide Limited FLTRK

This guide covers every exterior light bulb position on the 2026 Harley-Davidson Road Glide Limited (FLTRK), including the headlight (low/high beam), front and rear turn signals, tail/brake light, Tour-Pak lights, running lights, and license plate lights. The Road Glide Limited is a fully dressed model with the signature shark-nose fairing and integrated Tour-Pak luggage, featuring additional lighting compared to the base Road Glide.

Quick Reference Bulb Table

Difficulty & Time Estimate

• Difficulty Level: Beginner to Intermediate (2 out of 5 — more positions due to Tour-Pak)
• Estimated Time: 45-75 minutes because of Tour-Pak light access
• Best Done: In a well-lit area with the bike on a stand or level surface

Complete Tool List

OEM Part Numbers & Aftermarket Alternatives

Step-by-Step Instructions

Headlight (H13) — Low and High Beam

The 2026 Road Glide Limited uses a 7-inch H13 (9008) dual-filament headlight housed behind the signature shark-nose fixed fairing.

Step 1: Turn the ignition OFF and allow the headlight to cool for at least 10 minutes.

Step 2: Using a T-25 Torx driver, remove the three or four screws securing the headlight trim ring to the shark-nose fairing. Set aside in a small container.

Step 3: Carefully pull the trim ring away from the fairing and set it on a clean, soft surface. Access to the headlight on the Road Glide is somewhat tighter than the batwing models due to the fixed fairing design. You may want a small right-angle Torx for reinstallation.

Step 4: Disconnect the H13 electrical connector from the bulb base by pressing the release tab and pulling the connector body straight off.

Step 5: Release the wire retainer clip holding the bulb by pressing inward on the clip and sliding it to the side.

Step 6: Pull the old H13 bulb straight out. Do not grip the glass — handle by the metal base.

Step 7: Take the new H13 bulb and handle it by the base only. Use nitrile gloves if handling halogen. Clean any glass contact with isopropyl alcohol.

Step 8: Insert the new bulb into the reflector housing. Align the three tabs (wider tab for orientation). Push firmly until the bulb is fully seated.

Step 9: Reinstall the wire retainer clip by pressing inward and sliding it back into position over the bulb tabs. Verify it is secure.

Step 10: Reconnect the electrical connector firmly until it clicks.

Step 11: Test both low beam and high beam before reinstalling the trim ring.

Step 12: Position the trim ring and reinstall all screws. Tighten evenly and snug.

Step 13: Check headlight beam alignment using the wall method below.

Front Turn Signals (1157NA) — Amber

Step 1: Turn the handlebars for access to the fork-mounted turn signal housings.

Step 2: Pull back the rubber access grommet behind each turn signal.

Step 3: Turn the socket counterclockwise and pull straight out.

Step 4: Remove the old 1157NA bulb (push in, turn counterclockwise).

Step 5: Install the new amber 1157NA bulb (push in, turn clockwise).

Step 6: Test the turn signal before reassembly.

Step 7: Reinsert the socket and turn clockwise.

Step 8: Reseat the rubber grommet fully.

Rear Turn Signals (1157NA) — Amber

Step 1: Access the rear turn signals from behind the rear fender.

Step 2: Pull back the rubber access grommet.

Step 3: Turn the socket counterclockwise and remove.

Step 4: Replace the 1157NA bulb (push in, turn counterclockwise to remove; push in, turn clockwise to install).

Step 5: Test and reassemble.

Tour-Pak Top Turn Signals (1157NA) — Amber

Step 1: Access the light cluster at the top of the Tour-Pak. Remove the Tour-Pak cover or access from inside.

Step 2: Identify the turn signal bulb sockets within the Tour-Pak light cluster assembly.

Step 3: Turn each socket counterclockwise and remove.

Step 4: Replace the 1157NA amber bulbs.

Step 5: Test from the switch before reassembly.

Step 6: Reinsert the sockets and rotate clockwise.

Tail / Brake Light (1157) — Dual Contact

Main Tail Light:

Step 1: Locate the tail light housing on the rear fender extension below the Tour-Pak.

Step 2: Remove the T-25 screws (typically two) holding the housing to the fender bracket.

Step 3: Pull the housing back to expose the sockets.

Step 4: Identify the 1157 tail/brake socket (center).

Step 5: Turn the socket counterclockwise to remove.

Step 6: Replace the 1157 bulb.

Step 7: Test dim tail, bright brake, and turn signal.

Step 8: Reinstall the housing and T-25 screws.

Tour-Pak Tail / Brake Light:

Step 1: Access the Tour-Pak lower tail light from underneath or inside.

Step 2: Unclip or unscrew the lens housing.

Step 3: Turn the 1157 bulb socket counterclockwise and remove.

Step 4: Replace the 1157 bulb (push, turn clockwise to install).

Step 5: Test and reassemble the lens housing.

License Plate Light (194 / W5W / T10)

Main License Plate:

Step 1: Locate the license plate light on the rear fender near the plate.

Step 2: Reach up from below the fender to find the wedge-base socket.

Step 3: Pull the socket straight out (no twist).

Step 4: Replace the 194 bulb and reinsert the socket.

Step 5: Verify illumination.

Tour-Pak License Plate:

Step 1: Access the Tour-Pak rear plate light from inside the Tour-Pak or from below.

Step 2: Pull the wedge-base socket and replace the 194 bulb.

Step 3: Test and reinsert the socket.

Front Running Lights (1157)

The front running lights are handled by the same 1157 dual-filament bulbs used in the front turn signals — dim filament for running light, bright filament for turn signal.

Auxiliary Lamps (H11) — If Equipped

Step 1: Locate the auxiliary lamps on the lower fairing supports or engine guard braces.

Step 2: Remove the rear dust cover (turn counterclockwise).

Step 3: Disconnect the electrical connector.

Step 4: Release the wire retainer and remove the H11 bulb.

Step 5: Install the new H11 bulb, secure with retainer, and reconnect the wiring.

Step 6: Test with the ignition on.

Tips, Warnings & Common Mistakes

Headlight Alignment After Replacement

The Road Glide Limited's shark-nose fairing makes headlight access slightly more restricted than the batwing. Follow this procedure:

1. Park on level ground, 25 feet from a flat wall.
2. Measure headlight center height from ground.
3. Draw reference lines on the wall at measured height and 2 inches below.
4. With low beam on, the bright zone cutoff should be at or below the lower line.
5. Loosen the adjustment screws on the housing, adjust, and retighten. Use a small right-angle Torx if access is limited.

LED vs. Halogen — Pros and Cons

LED Flasher Warning: Use load equalizers or an LED-compatible flasher relay (H-D 68888-05) when replacing turn signal bulbs with LEDs to prevent hyper-flashing.

Legal Notes

• Compliance with DOT/FMVSS 108 is required for road use.
• Amber turn signals are mandatory — clear bulbs behind amber lenses may be illegal in some states.
• Headlight LED color above 6000K may fail inspection.
• The 2026 touring platform uses CAN bus — use CAN-bus-ready LED products.

Common Mistakes to Avoid

Verification Notes for 2026 Model Year

The 2026 Road Glide Limited features the new Touring frame and revised shark-nose fairing. Verify the following against your owner's manual:

To verify all specifications, check your 2026 Road Glide Limited owner's manual included with the motorcycle, or access it through the Harley-Davidson mobile app.

This guide was prepared using Harley-Davidson OEM service manual specifications and established industry bulb cross-references for the FLTRK touring platform. Always verify against your specific owner's manual before performing maintenance.

Parts for this job

Fits FLTRK, FLTR, FLT, FL — from our catalogue of 41,000+ aftermarket parts.

Stock Style Tail Lamp Replacement Lens Clear$7.02Tail Lamp Lens Plastic Clear Top$10.6412 Volt Bulb$12.02Spring Fork Spotlamp Bulb 12 Volt$12.02Tail Lamp Lens Laydown Style Red$12.80Tail Lamp Stock Type Red Plastic Lens$12.80Spring Fork Spotlamp Bulb 6 Volt$12.80Tail Lamp Lens Plastic Red$12.80*UPDATE Tail Lamp Lens Stock Clear$12.94*UPDATE Tail Lamp Lens Laydown Style Clear$12.94*UPDATE Tail Lamp Lens Laydown Style Red$12.94*UPDATE Tail Lamp Plastic Clear Lens$12.94